Orgonite, So I got my metal what now?

[sarrin]

Right so i have got some steel shavings, its in long coils 6 inches long or so, should i cut the coils up into small bits? Iam going to get a pyramid mold of some kind, and as i understand it i need 5 quarz crystals one double terminated For the center and 4 single terminated ones for each corner of the pyramid.. What type of resin should i use? and should i put as much metal in as i can or are there some specific quanties?

Thanks in advance

[paolo]

One single chunky quartz would probably do. Dont need to cut up those spirals too much. Spirals are good. Polyester resin - the finest if you can afford it but the cheapest if you can't. Go along with your intuition with what's right
If it's right for you, it's right

[guuna]

just cast my first bit of orgonite yesterday. just waiting for it to finish setting, hhg.

[tothestars]

Right so i have got some steel shavings, its in long coils 6 inches long or so, should i cut the coils up into small bits? Iam going to get a pyramid mold of some kind, and as i understand it i need 5 quarz crystals one double terminated For the center and 4 single terminated ones for each corner of the pyramid.. What type of resin should i use? and should i put as much metal in as i can or are there some specific quanties?

Thanks in advance

What are you gonna use it for ?

[alrick888]

I was recently sent the link to this site, where they have tutorials for making TBs, HGHs andd CBs with pictures: :cool:

http://www.materiaetherica.com/tutorials.html

Where did you get the metal shavings btw?

[xpleet]

There are many tutorials on the net and on youtube, you should google them all.

Wizzer's workshop is interesting, too.


I would suggest not to use Pyramids but round shapes. Pyramids are based of squares and squares make a rather rough, not smooth ride for all kinds of energies.

[sarrin]

In respose to tothestars

I Just want to make a few hhg's just to put in my room and around the house

[biblegirl]

Right so i have got some steel shavings, its in long coils 6 inches long or so, should i cut the coils up into small bits? Iam going to get a pyramid mold of some kind, and as i understand it i need 5 quarz crystals one double terminated For the center and 4 single terminated ones for each corner of the pyramid.. What type of resin should i use? and should i put as much metal in as i can or are there some specific quanties?

Thanks in advance

Hello Sarrin :). I tend to have a bit of trouble with the longer coiled pieces, because when I am arranging them tightly into the mold, sometimes they expand and pop out a little above the level that the resin will be poured. Then when I try to push them back in, it causes another coil to pop out the top...to avoid this, i like to separate them into smaller more manageable pieces before pouring.

While pouring, i try to keep all the metals about an inch below the fill line, that way I don't have shards or sharp pieces sticking out of the finished orgonite. Yes try to pack the metal in there. I haven't used a pyramid mold yet, but martini glasses are really simple and turn out nice HHGs. Spray them with silicone lubricant or WD-40 and the finished orgonite will come out easily. I use one single terminated crystal for these, set vertically. You will find the 5 crystal plan on a lot of tutorials as it was the original design, but it does not necessarily make a stronger piece than a single crystal :).

I use polyester resin from a fiberglass store. Sometimes they have it at hardware stores, as well as at craft stores for a pretty penny :D. Good luck with everything! Any more questions, feel free to post!

[sarrin]

Thanks biblegirl that has cleared things up a bit. That Orgonite experiment post you did really inspired me to make orgonite and research about it. :D

[biblegirl]

Thanks biblegirl that has cleared things up a bit. That Orgonite experiment post you did really inspired me to make orgonite and research about it. :D

Thank you, I'm very happy to help :). Here is a link to my new Q&A thread on orgonite: http://davidicke.com/forum/showthread.php?t=71354

[sarrin]

Yeh i have already taken a look at that. I have got all my things now and plan on making my first hhg this weekend. The DT quartz crystals i got, certainly have a feel about them cant put my finger on it. They just feel good to hold

[doctor_john]

I would try adding conductive carbon if you could get a hold of it, the powder form would be good, mix this with the resin then pour over onto you mix.